Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation


Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   + 3.1. Engines 2F and 3F-E
   - 3.2. Verkhneklapanny engine 1FZ-FE
      3.2.1. Technical characteristics
      3.2.2. Types of repair without engine dismantle
      3.2.3. Cover of a head of cylinders
      3.2.4. A soaking-up collector
      3.2.5. Final collector
      3.2.6. Cam-shafts and pushers
      3.2.7. Head of cylinders
      3.2.8. Cover of a chain drive of cam-shafts
      3.2.9. Forward epiploon of the crankshaft
      3.2.10. Oil pallet
      3.2.11. Oil pump
      3.2.12. Flywheel (a leading disk of the hydrotransformer)
      3.2.13. Back epiploon of the crankshaft
      3.2.14. Suspension bracket and engine details
   + 3.3. Dismantle and major maintenance of the engine
   + 3.4. Engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes









3.2.10. Oil pallet

 Removal
PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Put the car on the hand brake and block back wheels.
3. Lift a car front.
4. Remove mud guards of the engine.
5. Merge oil and remove the oil filter. Remove a masloukazatel.
6. Remove the stabilizer of a forward suspension bracket (see subsection 9.2).
7. Remove exhaust pipes assembled.
8. Remove the sensor of level of oil and examine.
9. Unscrew pallet 2 bolts (the bottom section).
10. Carefully separate and remove the bottom section.
11. Unscrew bolts (are specified by shooters a photo at the left) and nuts near a pulley (are specified by shooters a photo on the right) pallet 1 (top section).
12. Open consolidation and carefully separate the top section.
13. Incline and remove the top section.
14. Unscrew nuts of fastening of a maslopriyemnik (are specified by shooters).
15. Unscrew nuts of maslootrazhatel (are specified by shooters) and remove a maslopriyemnik.

Installation

PERFORMANCE ORDER
1. Remove from the demountable planes of the block of cylinders and the pallet the consolidation remains. Wash out the condensed planes solvent.
2. Be convinced of purity of carving openings in the block of cylinders.
3. Check existence on the demountable plane of the pallet of deformations, especially about openings under bolts. If necessary отрихтуйте the plane a hammer on a board.
4. Check a condition of a maslopriyemnik, existence on it of cracks and a contamination of the filter of rough cleaning. Establish a tube of a maslopriyemnik.
5. Check a condition of the sensor of level of oil and the socket. Replace laying.
6. At assembly establish new laying of a maslopriyemnik in a forward cover.
7. Put 3 mm rollers of hermetic on the condensed plane of the pallet 1.
Prevention

The detail should be established no later than 5 minutes after hermetic drawing.
8. Carefully establish the pallet and wrap bolts. In three-four receptions tighten pallet bolts with the set moment, beginning an inhaling in the central part.
9. Put 3 mm rollers of hermetic on the pallet 2 plane, establish the pallet, evenly and gradually tighten bolts with the set moment.
10. Further assembly are carried out upside-down. Fill in oil in the engine and replace the filter. Replace laying of an exhaust pipe of the exhaust silencer.
11. Start the engine and be convinced of lack of a leak.