Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
- 9. Suspension brackets and steering
9.1. Technical characteristics
9.2. Stabilizer of a forward suspension bracket and plug
9.3. Lobbies and back shock-absorbers
9.4. Springs and plugs
9.5. Springs of suspension brackets (and/m FJ80)
9.6. Cross-section bar (and/m FJ80)
9.7. Suspension bracket levers (and/m FJ80)
9.8. Rotary fist
9.9. Steering wheel
9.10. Steering drafts
9.11. Reducer
9.12. Pump of the hydraulic booster
9.13. Air removal from the power steering
9.14. Wheels and tires
9.15. Corners of installation of forward wheels
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes
|
Details of the steering mechanism of FJ60 cars, 62
1. Quencher of fluctuations
2. Шплинт
3. Soshka
4, 19. Tip of leading draft
5. Cover
6. Cap
7. Spring
8. Sharovy finger of a tip of draft
9. Шплинт |
10. Tip of leading draft
11. Saddle
12. Loose leaves of a spherical finger
13. Butterdish
14. From a soshka
15, 18. A tip of conducted draft
16. From conducted draft
17. Conducted draft
20. Lever of a rotary fist |
Details of the steering mechanism of FJ80 cars
1, 4, 6, 10. Tip of leading draft
2. Draft
3. Collar
5. Soshka |
7. Quencher of fluctuations
8. Arm
9. Leading draft
11. Шплинт |
Check
| PERFORMANCE ORDER |
| 1. Turn of wheels is provided with effort transfer from a wheel reducer through a soshka, steering drafts and tips of drafts. Parallel to a soshka of a wheel the quencher of fluctuations of a steering wheel is attached. |
| 2. Expose wheels in the provision of driving on a straight line and block a steering wheel. |
| 3. Lift the car so that the wheel appeared approximately in 2,5 cm from the earth. |
| 4. Check люфт in tips of drafts. For this purpose establish the indicator so that his leg rested against the wheel region. Slightly shake a wheel in the horizontal plane. If the indication of the indicator exceeds 6 mm, it is necessary to check a condition of all tips of drafts and to replace worn-out details. |
| 5. Lift a front of the car and check a condition of covers of tips of drafts and steering drafts, and also jamming sharnirny connections. |
|
Removal and installation
TIPS OF CONDUCTED DRAUGHT
| PERFORMANCE ORDER |
| 1. Remove a wheel. |
|
|
2. Rasshplintuyte also release a koronchaty nut of the spherical hinge, a nut completely not to turn on. |
|
|
3. A stripper выпрессуйте a hinge finger from an eye of the lever of a rotary fist. |
|
4. At replacement of a tip count number of strings of a carving (it is specified by an arrow) on which will wrap a tip. Release a collar and turn out a tip. |
| 5. Grease a carving part of a tip with konsistentny greasing and turn in draft so that the end face of a tip defended from draft on number of strings of the carving, defined before removal. A collar not to tighten. |
| 6. Insert a finger into an eye of the lever and wrap a nut. The finger should come into an eye densely. If the finger rotates in a lever eye at a nut tightening, press it into a konusny opening. |
| 7. Replace шплинт, if necessary tighten a nut before coincidence of a groove of a nut to an opening under шплинт in a carving part of a finger. |
Prevention
It is forbidden to turn on a nut to provide free passing шплинта.
|
| 8. Tighten nuts of collars. |
| 9. Establish a wheel and lower the car. |
|
LEADING DRAUGHT
| PERFORMANCE ORDER |
| 1. Lift one party of the car. |
| 2. Disconnect from leading draft a quencher of fluctuations (see subitem 2 and 3). |
| 3. Disconnect draft from a soshka of a shaft of a reducer, a rotary fist (or conducted draft on FJ 60,62 cars), having executed actions on subitem 2 and 3. |
| 4. If necessary replace tips, having executed the corresponding actions on change of tips of conducted draft. |
| 5. Assembly is carried out upside-down. Tighten all fastenings with the set moment. |
|
SOSHKA
| PERFORMANCE ORDER |
| 1. Disconnect leading draft. |
| 2. Will release a soshka nut. Designate the provision of a soshka concerning a reducer shaft. |
|
|
3. Remove a soshka. |
| 4. Unscrew a nut and remove a soshka. |
| 5. Assembly is carried out upside-down. Combine the labels put at dismantling. |
|
QUENCHER OF FLUCTUATIONS
| PERFORMANCE ORDER |
| 1. Disconnect a quencher of fluctuations, having executed actions according to item 2. |
|
|
2. Unscrew a nut (it is specified by an arrow) fastenings to a frame and remove a quencher of fluctuations. |
| 3. Installation is carried out upside-down. Tighten nuts with the set moment. |
|
|
|