Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation

Toyota Land Cruiser
+ 1. Maintenance instruction
+ 2. Maintenance
- 3. Engines
   - 3.1. Engines 2F and 3F-E
      3.1.1. Technical characteristics
      3.1.2. Types of repair without engine dismantle
      3.1.3. Installation of the piston of the 1st cylinder in VMT
      3.1.4. Cover of a head of cylinders
      3.1.5. Lateral cover of the mechanism of a gazoraspredeleniye
      3.1.6. Yokes and bars of pushers
      3.1.7. Springs of valves, plates, maslosjemny caps
      3.1.8. Soaking-up and final collectors
      3.1.9. Head of cylinders
      3.1.10. Pushers
      3.1.11. Crankshaft pulley
      3.1.12. Forward epiploon of the crankshaft
      3.1.13. Forward cover
      3.1.14. Cam-shaft and drive gear wheels
      3.1.15. Cam-shaft and support
      3.1.16. Replacement of bearings
      3.1.17. Oil pallet
      3.1.18. Oil pump
      3.1.19. Flywheel (a leading disk of the hydrotransformer)
      3.1.20. Back epiploon of the crankshaft
      3.1.21. Suspension bracket and engine details
   + 3.2. Verkhneklapanny engine 1FZ-FE
   + 3.3. Dismantle and major maintenance of the engine
   + 3.4. Engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes

3.1.8. Soaking-up and final collectors

GENERAL INFORMATION

Designation of bolts of fastening of collectors on the engine 3F-E

Bolt And and In turnkey 17 and 14

With – a nut

Prevention

Works are carried out on the cold engine.

Removal

PERFORMANCE ORDER

1. Disconnect the battery from weight.
2. Merge liquid from cooling system.
3. Remove the carburetor or the leveling chamber (see subsection 5.1.8.3 and subsection 5.2.9.2.6).
4. Remove the air pump and an air collector (see subsection 6.3).
5. Unscrew bolts and remove an arm of a final collector.
6. Disconnect the highway from the fuel distributor (on injector engines, see subsection 5.2.9.2.5).
	7. Remove a thermal guard.
8. Remove the pump of the hydraulic booster and take aside, without disconnecting the highway.
9. On cars with automatic transmission disconnect draft of a throttle of transmission.
10. Disconnect a retsirkulyatsiya tube (see subsection 3.2.4).
11. Unscrew 2 bolts and 2 nuts of fastening of an exhaust pipe to a collector.
12. Disconnect the socket from the oxygen sensor.
	13. Unscrew bolts and nuts, remove dividing plugs. Remove collectors.

Installation

PERFORMANCE ORDER

1. Clear the planes of the consolidation remains.
2. If the collector changes, rearrange on a new collector all details from the replaced.
3. Establish new laying and collectors.
	4. Tighten bolts and nuts in the specified sequence, with the set moment (see fig. Designation of bolts of fastening of collectors on the engine 3F-E).
5. Establish all removed details upside-down.
6. Start the engine and be convinced of lack of a leak.