Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
2.1. Additional maintenance
2.2. Technical characteristics
2.3. An arrangement of units in a motor compartment
2.4. Maintenance terms
+ 2.5. Check of level of liquids
2.6. Check of a condition of tires and pressure in tires
2.7. Liquid level in automatic transmission
2.8. Liquid level in system of a hydraulic actuator of a steering
2.9. Oil replacement in the engine and the oil filter
2.10. Check of a condition and care of the battery
2.11. Check of system of cooling
2.12. Check and replacement of hoses in a motor compartment
2.13. Check and replacement of brushes of a cleaner of a windscreen
2.14. Shift of wheels
2.15. Suspension bracket and steering check
2.16. Check of an exhaust system
2.17. Check of level of oil in a manual transmission
2.18. Check of level of oil in a transfer case
2.19. Check of level of oil in reducers of bridges
2.20. Check of a condition of seat belts
2.21. Thermostat of the air filter (carburetor engines)
2.22. Check and greasing of the exhaust valve
2.23. Catching system паров gasoline
2.24. Check of system of a retsirkulyatsiya
2.25. Air zaslonka of the carburetor
2.26. Zolotnik of system of ventilation of a case
2.27. Check and replacement of the air filter
2.28. Replacement of spark plugs
2.29. Check and adjustment of gaps of valves
2.30. Idling turns (carburetor engines)
2.31. Drive belts
2.32. Check of fuel system
+ 2.33. Check of brakes
2.34. Check and adjustment of pedals of coupling (brake)
2.35. Replacement of the fuel filter
2.36. High-voltage wires, begunok and distributor covers
2.37. Check and installation of the moment of ignition
2.38. Care of cooling system
2.39. Naves and bearings of forward wheels
2.40. Liquid replacement in automatic transmission and the filter
2.41. Oil replacement in a manual transmission
2.42. Oil replacement in a transfer case
2.43. Oil replacement in a back (forward) reducer
2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes
|
Set of tools for replacement of spark plugs
|
|
1. Candle face key
2. Dinamometrichesky key
3. Graggers
4. Adapter
5. A set of calibres for gap check between candle electrodes |
Adjustment
| PERFORMANCE ORDER |
| 1. Prepare tools and adaptations. At replacement of candles it is necessary to get new candles of recommended type, to expose a gap and to screw instead of old, replacing each candle separately. |
| 2. Check a condition of new candles. At detection of any signs of damages of an insulator I shine to establish it is impossible. |
|
|
3. Check a gap between electrodes of new candles in calibre of round section. The gap between electrodes should correspond specified in the podkapotny plate. |
|
4. If the gap does not correspond to norm, turn in an electrode by means of the lever on the case of a set of calibres. |
| 5. If the lateral electrode does not coincide with central, turn in the lever on the case of a set of calibres before combination of both electrodes on the candle center. |
|
Removal
| PERFORMANCE ORDER |
|
|
| 1. On the engine 1FZ-FE for access to candles take a slip (a photo at the left). Turn a tip on a half of turn, at the same time making the effort directed up, and get a wire (a photo on the right). |
| 2. Blow the place pump round a candle, having removed dirt. |
| |
3. Turn out a candle a natural the extension piece. |
| 4. Irrespective of, whether the candle will change, or to be turned old, check a candle condition. |
|
Installation
| PERFORMANCE ORDER |
|
|
1. Before a wraparound of a candle it is into place recommended to grease a carving with structure against прихвата. |
|
2. To wrap a candle without distortions dress on a candle a hose piece with internal diameter of 9,5 mm. As soon as the candle will start to be wrapped with a distortion, the hose will start to be scrolled on an insulator owing to what carving damage is prevented. |
| 3. Tighten a candle with the set moment. |
| 4. Establish a tip, having turned on a half of turn and having at the same time made the effort directed down. |
| 5. In a similar order replace other candles. |
|
|
|