Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation

Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Check of an exhaust system
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. Catching system паров gasoline
   2.24. Check of system of a retsirkulyatsiya
   2.25. Air zaslonka of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, begunok and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a transfer case
   2.43. Oil replacement in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes

2.39. Naves and bearings of forward wheels

Check and greasing replacement

1. Bearings of forward wheels should be checked wheel rocking at each raising of a front.
2. At detection люфта when rocking in the vertical plane it is necessary to disassemble knot and to check a condition of bearings.
3. Remove a wheel.
4. Remove a support, take aside and fix.
5. Remove the mechanism of blocking of naves (see subsection
6. To Raskontrita an external nut also unscrew.
7. Cнимите a washer, unscrew an internal nut.
8. Cнимите persistent washer.
9. Submit a nave on itself and back, get the external bearing.
10. Remove a nave.
11. Get an epiploon.
12. Remove the internal bearing.
13. Carefully wash out a nave and bearings solvent and dry.
14. Examine bearings and external holders. At detection of damages replace the bearing for what beat out a holder to brass small beards and press the new.
15. Put in the bearing refractory greasing.
16. Grease with a thin layer of a neck of a nave, internal surfaces of holders of bearings, epiploons and boring under an epiploon.
17. Put greasing in a nave cavity between external holders, having formed a finger a greasing fillet along the edges of holders.
18. Establish the internal bearing in a nave and cover with greasing a bearing end face.
19. Press an epiploon aflush with a nave surface.


1. Establish a nave and the external bearing.
2. Dress a washer and wrap an internal nut with the moment of 51 N of m, at the same time turning a nave.
3. Release a nut and again tighten with the moment of 4,8 N of m, at the same time turning a nave. Be convinced that люфт is absent, and the wheel rotates freely.
4. Dress a lock washer and tighten an external nut with the moment of 56 N of m. Check люфт, at existence люфта перезатяните an internal nut. Bend kontrovochny ledges of a washer in opposite directions.
5. Further assembly is conducted upside-down. Slightly grease litoly knot of blocking of a nave (excess of greasing is not allowed).