Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation

Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Check of an exhaust system
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. Catching system паров gasoline
   2.24. Check of system of a retsirkulyatsiya
   2.25. Air zaslonka of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, begunok and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a transfer case
   2.43. Oil replacement in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes

2.9. Oil replacement in the engine and the oil filter

GENERAL INFORMATION

Timely replacement of oil is the most effective measure applied by the owner to avoid premature wear of the engine owing to aging of oil, its razzhizheniye and pollution.

PERFORMANCE ORDER

1. For ensuring access to the lower part of the car, it is necessary to establish the last on two supports with a cross-piece, either to lift a telfer, or to call in on a hole or a platform.
2. Find a drain stopper of the pallet of the engine.
3. Establish the car on a horizontal platform. Warm up the engine, stop and unscrew a stopper of a maslozalivny mouth on a cover of a head of cylinders.
4. Lift the car and establish on supports.
	5. Carefully, trying not to concern hot details of an exhaust system, substitute the pallet and unscrew a stopper.
6. Merge oil, check existence in the merged oil of metal shavings and sawdust.
7. After running off of oil wipe a stopper pure rags.
8. Wipe the pallet about a drain opening and carefully tighten a stopper.
9. Substitute the pallet under the oil filter.
10. Clean from under the car all tools and lower the car.
	11. By means of a special key unscrew the oil filter (it is specified by an arrow) (to rotate counter-clockwise) then turn out the filter hands.
12. Carefully clear a place of a prileganiye of consolidation of the filter on the block of cylinders.
	13. Be convinced that the type and the sizes of the new filter completely coincide with type and the sizes of the fulfilled. Slightly oil for the engine rubber laying of the new filter and wrap the filter into place.
14. Wrap the filter before contact of laying with a surface of the block of cylinders, tighten the filter, having turned on 3/4 turns.
15. Fill in about 3 l of oil, having a little waited, check oil level. If level normal, wrap a stopper of a mouth and tighten by hand. Start the engine that oil filled all lubricant channels.
16. On the working engine check tightness of a stopper of the pallet and the filter, having tracked these places within a minute. At emergence of a leak stop the engine and tighten a stopper or the filter.
17. Stop the engine and wait some minutes that oil flew down in the pallet. Again check oil level on щупу. If necessary add oil to the top mark on щупе.
18. In we say lies several trips after oil change in the engine watch a leak and check oil level.