Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. Maintenance instruction
- 2. Maintenance
   2.1. Additional maintenance
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance terms
   - 2.5. Check of level of liquids
      2.5.1. Oil level in the engine
      2.5.2. Cooling liquid
      2.5.3. Liquid of a washer of a windscreen
      2.5.4. Electrolit of the storage battery
      2.5.5. Liquid of a hydraulic actuator of brakes and coupling
   2.6. Check of a condition of tires and pressure in tires
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydraulic actuator of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Check of an exhaust system
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a transfer case
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. Thermostat of the air filter (carburetor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. Catching system паров gasoline
   2.24. Check of system of a retsirkulyatsiya
   2.25. Air zaslonka of the carburetor
   2.26. Zolotnik of system of ventilation of a case
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of gaps of valves
   2.30. Idling turns (carburetor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   + 2.33. Check of brakes
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, begunok and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a transfer case
   2.43. Oil replacement in a back (forward) reducer
   2.44. Gaps in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and steering
+ 10. Body
+ 11. Electric equipment
+ 12. Electroschemes




2.5.1. Oil level in the engine

GENERAL INFORMATION

Shchup masloukazatel (engines 2F and 3F-E)

Shchup of a masloukazatel (1) on engines 2F and 3F-E is located on the right side.

Shchup masloukazatel (engines 1ZF-FE)

Shchup of a masloukazatel (it is specified by an arrow) on engines 1ZF-FE is located on the left side.

Check of level of oil – an important preventive measure of operations of maintenance. If oil level constantly goes down, the reason are an oil leak through the damaged epiploon, the weakened connections, or through piston rings or directing plugs of valves. If oil gets a dairy shade or in oil water drops are observed, tightness of laying of a head of cylinders is broken. All this indicates need of immediate check of the engine. It is necessary to check an oil condition also regularly. Each time during check of level of oil before wiping щуп, clamp щуп two fingers and carry out on it up. If it is visible that between fingers and shchupy the remains of dirt or small metal particles get stuck, it is necessary to replace oil.

PERFORMANCE ORDER
1. Check oil level shchupy which is inserted into a branch pipe of the oil pallet of the engine.
2. Check oil level on the cold idle engine, or about 15 minutes later from the moment of its stop. If check of level of oil to make right after a trip, some part of oil remains in the top part of the engine and results of check will be erroneous.
3. Get control щуп from a tube and wipe it a pure rag or a paper napkin. Insert pure щуп back into a tube and again get. Check level on an oil film.
4. Level of oil should is between risks of L and F control щупа. Otherwise oil add (the amount of oil corresponding to change of level from a mark L to a mark F, makes near 1л).
5. If level of oil is higher than a mark F, it will lead to a zamaslivaniye of candles, leakage of oil, or to epiploon failure.
6. To add oil, turn out a mouth stopper (it is specified by an insole) on a cover of a head of cylinders.